PowerHouse Lithium has optimized this charger for use with our lithium iron phosphate batteries (LiFePO4). Bank 1 is rated for 10A for charging lead acid or AGM 12V cranking batteries. Bank 2 is 24v 10A for 24v PowerHouse Lithium batteries! Even when running 2 of our 36v PowerHouse Lithium batteries in parallel this one charger will charge both at the same time. This charger is 100% waterproof and can be mounted onboard your boat as you normally would with marine battery chargers. All 24 volt PowerHouse Lithium Batteries batteries should be charged using a LiFePO4 compatible charger like this one. SLA chargers will reduce the performance and lifespan of the battery.
This charger has a built in wake up feature to reset BMS to start the charging process if you fully discharge your lithium battery. The activation button starts the charge cycle into the battery waking up the BMS and allowing charge to start entering the battery.
This charger works with Run & Gun 12v and 16v models, and all units are waterproof and vibration tested.
This unit comes with a 2 year warranty.
SIZE - 11.5" x 9.6" x 3.9"
FOR 12 and 24 VOLT LITHIUM BATTERIES
We highly reccomend you use a LiFePO4 compatible charger. 36v chargers for lead acid batteries may work, but will decrease performance and lifespan of the battery.
CHARGER RATING
INPUT 100-240 volts, 50/60HZ. OUTPUT: 14.4 volts, 15.0 amps, 24 volts, 10.0 amps.
TERMINAL CONNECTIONS
Connect black to your black terminal. Red to your red terminal. Do not short circuit. Red light on the charger will turn on when charging. Light turns green when the battery is full.
SMART BMS COMMUNICATION
Charger will restart or "wake up" a BMS that has turned off a battery due to short circuit or excessive amp draw. Simply connect the charger to the battery to initiate a restart.
WARRANTY
This battery charger comes with a 2 year warranty through PowerHouse Lithium.
USD : 87.5
WASHING INSTRUCTIONS:
Machine wash separately in cold water on a gentle cycle. Tumble dry separately on low heat. Add QE Home Wool Dryer Balls to reduce wrinkles and increases drying efficiency. Touch up with a low heat iron as needed. Do not bleach or dry clean.
![C.E. Smith Screwless Flush Mount Rod Holder 15 Degree Black Liner No Logo [53677]](https://cdn.shopify.com/s/files/1/2208/5969/files/108261XL.jpg "C.E. Smith Screwless Flush Mount Rod Holder 15 Degree Black Liner No Logo [53677]")
![C.E. Smith Single Aluminum 5 Degree Transom Mount Rod Holder [53750]](https://cdn.shopify.com/s/files/1/2208/5969/products/62254XL.jpg "C.E. Smith Single Aluminum 5 Degree Transom Mount Rod Holder [53750]")
![C.E. Smith PWC Dolly [27575]](https://cdn.shopify.com/s/files/1/2208/5969/products/39079XL.jpg "C.E. Smith PWC Dolly [27575]")
![C.E. Smith Spare Tire Carrier w/Lug Nuts [27200]](https://cdn.shopify.com/s/files/1/2208/5969/products/42936XL.jpg "C.E. Smith Spare Tire Carrier w/Lug Nuts [27200]")
![C.E. Smith Screwless Flush Mount Rod Holder 0 Degree Black Liner No Logo [53676]](https://cdn.shopify.com/s/files/1/2208/5969/files/108260XL.jpg "C.E. Smith Screwless Flush Mount Rod Holder 0 Degree Black Liner No Logo [53676]")
